Second electromagnet rebuilt and everything is working as expected!

As a restoration, it’s pretty much complete now. Normally the finished top would be attached to the upper frame, but as I want to display it, I decided to make it lift off, so I don’t have to unscrew the thumb screws for the upper frame to see the insides.

Just need to finish off my extras on it.

I found an antique servants bell on eBay which should arrive during the week. It’s got a wood surround, which I’ll strip back and colour match to the block bell. Then I’ll wire it up and then it should be done!

My next problem is that I’ve not actually got anywhere to put it! I’ll have to have a move around!

#makershour #woodworking #woodwork #railway #electronics

O dřevě #69

Mateřská škola v Dobřině ~ Kuchyň jako u babičky ~ Kaple v Nesvačilce ~ Alpský bivak ~ Dřevostavba čerpá z funkcionalismu

Woodinsider

Ein Küchenorganizer aus Eichenholz. Ein Projekt für Zwischendurch ⚒️.

Es macht immer wieder Spaß mit Eichenholz zu arbeiten.

#diy #handmade #selfmade #upcycle #upcycling #recycle #recycling #woodArt #woodwork #woodworking #woodenart #nature

IT’S ALIVE!!

Only running on one electromagnet at the moment. Need to recoil the other one, but I need some more wire.

I’ve obviously taken some poetic licence on the bell wiring, as it wouldn’t normally ding unless it receives from another signal box. I’m hoping to rig it up to a simple door bell to imitate receiving.

As it’s for me and not for resale, I’m okay with that. It’s also possible to revert the wiring if I ever did want to sell it.

#makershour #woodworking #woodwork #railway #electronics

Sometime you just have to improvise!

Recoiling the electromagnet in an attempt to get some life into it.

#makershour #woodworking #woodwork #railway

My latest test #wand creation. The handle is wrapped with real leaves, which keep their colour under glue. I then used #pyrography to burn various patterns onto it.

#woodwork #crafting #woodburning #woodburningart #magic

30/10 Last two arolla pine spelts sections. My small carver Kalthoff axe and my Morakniv knife did a good job again today.

#handmade #fence #handsplit #heartwood #hardwork #woodwork #larch #arollapine #wood #art #sustainability
The first section of the fence in larch wood.
I wedged the first and last fence posts very accuratly with stones 80 cm deep. You could tie a wild bull to this posts.

Instead of using 150 cm nails, I should have used thick 120-130cm nails to nail down the crossbars. Wooden nails would have been even better. The 150 cm iron nails were a little too long and pierced some of the halved columns by a few millimetres and split some of the crossbar ends. When using thick nails on larch boards (especially near the board ends), you should always pre-drill a hole that (ca. 80% of the nail diameter), as iron nails have a strong splitting effect on larch wood (blunting the tip of the nail slightly reduces the splitting effect). I did this, but did not pre-drill.
The strong fence posts does not have to be predrilled at full lenght.
I started with wood nails, but that was too slow for the lady. The extra hour wouldn't have made any difference. After setting 8 larch wood nails, I switched to the too-long iron nails without pre-drilling. Didn't make the whole thing any better.

#handmade #fence #handsplit #heartwood #hardwork #woodwork #larch #arollapine #wood #art #sustainability
30/10 I also like the variety provided by the last two sections made of arolla pine wood spelts. Both larch and and arolla pine are excellent woods for outdoor use, although arolla pine prefers dry conditions. If it is not constantly wet and can dry out thoroughly, the heartwood can also last for many decades.

#handmade #fence #handsplit #heartwood #hardwork #woodwork #larch #arollapine #wood #art #sustainability
×
The first section of the fence in larch wood.
I wedged the first and last fence posts very accuratly with stones 80 cm deep. You could tie a wild bull to this posts.

Instead of using 150 cm nails, I should have used thick 120-130cm nails to nail down the crossbars. Wooden nails would have been even better. The 150 cm iron nails were a little too long and pierced some of the halved columns by a few millimetres and split some of the crossbar ends. When using thick nails on larch boards (especially near the board ends), you should always pre-drill a hole that (ca. 80% of the nail diameter), as iron nails have a strong splitting effect on larch wood (blunting the tip of the nail slightly reduces the splitting effect). I did this, but did not pre-drill.
The strong fence posts does not have to be predrilled at full lenght.
I started with wood nails, but that was too slow for the lady. The extra hour wouldn't have made any difference. After setting 8 larch wood nails, I switched to the too-long iron nails without pre-drilling. Didn't make the whole thing any better.

#handmade #fence #handsplit #heartwood #hardwork #woodwork #larch #arollapine #wood #art #sustainability
My fence will also turn gray in a few years, but hopefully it will remain stable and durable for many many years.
@valentinzi Nice work. How long do they tend to last?
I don't know exactly. It's quite possible that this fence could last for several decades (perhaps 3-6 or even more) without any external influence. The wood is not only pure heartwood, but also old mountain wood that is still of good quality. I think the some of crossbars could possibly break or become loose. I used iron nails. Good wooden nails might be even more durable under certain circumstances.
There are fences of similar type in South Tyrol that are over fifty years old.
I think the fence next to it is about 15 years old, but it's time to replace it. Larch columns with sapwood at the top (at the end grain) and in the floor are starting to rot. Wedged in place with lots of stones all around (no contact with humus), including charred heartwood, it will certainly last longer here (perhaps 2-3 times as long).