| Homepage | https://buechner.me |
| OpenPGP key 0xA15ACACE7756A8A2 | https://buechner.me/pgpkey.php |
| Matrix | @ravage:xentonix.net |
| Gravatar | https://gravatar.com/akismetuser193662674 |
Nils
- 42 Followers
- 100 Following
- 514 Posts
System administrator, hobby programmer, Ubuntu member and part of the Ubuntu Matrix council
u880d
Thunderbird: Free Your InboxWe have a shiny new roadmap site, and an equally shiny new blog post to tell our community all about it:
https://blog.thunderbird.net/2026/03/introducing-our-public-roadmaps/
Introducing our Public Roadmaps - The Thunderbird Blog
At Thunderbird, we firmly believe in the strength of listening to our community’s needs and wants, and balancing it with our resources and capabilities. While this has always been part of our ethos, we want to start 2026 by making our goals easier to read and comprehend at roadmaps.thunderbird.net, where you will find our roadmaps […]
NathSomewhere, someone finally made this and I think it's beautiful: https://www.thingiverse.com/thing:4687836
Ethernet | RJ45 clip to secure/repair/fix broken tab by guss67
This clip was design to fix/repair/secure the broken or loose tab of a RJ45 Ethernet connector and avoid crimping. Designed to prevent from moving, wiggling, falling from the connector and easy to install.UPDATE v.4.9 | 28/01/2021Added the 3 following files which have slightly wider body (0.25mm) than 4.7 version and small upgrade on the tip.1. "4.9.nf.supported" (extension) comes "with supports" for the ones are not very familiar with. But I still prefer S3D's supports.2. "4.9.nf" (extension) with "no fillet", to make it easier printing with supports.3. "4.9" (extension) with fillet, for "smooth edges". On FDM printers isn't that much noticeable.UPDATE v.4.7 | 01/01/2021Added another version with "no fillet" (".nf" extension), actually it has sharp edges to make it easier printing with supports.PrintingSuggested printing orientation is the one as the files are stored, why?Printing the tab from the base to the tip in X-Y axis makes it stronger and more flexible since its printed in one continued string.If you change the orientation with the tip on top then tab's base will start from the bottom and builds up while the Z axis is sticking the rest of it till the tip. With this orientation the tab has more possibilities to brake since Z layers don't bond the same as the method I suggested.*If you have another solution let me know.Supports Supports needed and you need to be experienced with good slicer settings. Also attention needed when removing them from the actual print.Or you can print the file with "4.9.nf.supported" (extension) which comes with supports. But I still prefer S3D's supports.Installation note:1.Before install the "printed clip" check the left overs of the broken tab. If it is too long the tip of the "printed clip" might not click underneath the left-over. So, I suggest to leave a length of the broken tab about "0,5-1,0mm". If the broken tad left-over is to small or cuted flash then the printed one might not click and hopefully that would work well, haven't tested that scenario.2.Follow the sketches to install the "printed clip", also while sliding in if you find it a bit hard some wiggling might help.*You may call it the "ScorpioNet" or "Devil's Network Tail"! Designed in InventorIf you enjoy and want to support my work you can donate me on the link below,Thank you!
VessOnSecurity
amy
Richard HughesNext week we're planning a big #fwupd release (with a lot of new exciting stuff) but the translations are looking a bit sad. Can anybody help? Thanks.
publictorsten
Keep Android OpenWe have published an open letter to Google opposing the Android Developer Verification Program with over 30 organizations as signatories: https://keepandroidopen.org/open-letter/
Randahl FinkIn the age of disinformation, this is the most important episode of Last Week Tonight yet.
John Oliver uncovers how Elon Musk took over Twitter and began funding accounts who spread disinformation, creating movements that cause serious trouble in the real world based on Twitter falsehoods — even causing the Trump regime to launch security operations based on conspiracy theories invented by random Twitter users.
Twitter: Last Week Tonight with John Oliver (HBO)
Harley 🐝🌿- do you want to use google to sign in?
- do you want to add a passkey?
- do you want to add a 2FA token?
- we know you have 2FA but we've sent you an email instead
- this login attempt seems suspicious we've sent you a text about it
- can you click on these buses?
- you failed to click on the buses click on these bicycles instead
- should we save these details for next time?
- do you accept these trackers?
- you can opt out but we've decided it's legitimate interest anyway
- would you like to see a list of our 847 partners we share your data with?
- can we send you desktop notifications?
- can we access your location?
- do you want 10% off for signing up to the mailing list?
- do you want me to translate this page?
- hi I'm your friendly chatbot how can I help?
- oh no you can't buy this, reach out to us for a quote!
- do you want—
I'm tired boss