| Homepage | https://buechner.me |
| OpenPGP key 0xA15ACACE7756A8A2 | https://buechner.me/pgpkey.php |
| Matrix | @ravage:xentonix.net |
| Gravatar | https://gravatar.com/akismetuser193662674 |
Nils
- 42 Followers
- 100 Following
- 515 Posts
System administrator, hobby programmer, Ubuntu member and part of the Ubuntu Matrix council
@koehntopp Das kann man ja in der Bauchbinde dann einfach zu Automobil-Experte machen
u880d
@FinchHaven I recommend a little less wild guessing. There is no indication for any compromised system or service. Probably just a DDOS to that URL.
@FinchHaven This is not snap related at all. The service behind connectivity-check.ubuntu.com is/was under attack and was taken offline until mitigations can be put into place. Until then you can go to Settings -> Privacy -> Connectivity and disable the check.
Thunderbird: Free Your InboxWe have a shiny new roadmap site, and an equally shiny new blog post to tell our community all about it:
https://blog.thunderbird.net/2026/03/introducing-our-public-roadmaps/
Introducing our Public Roadmaps - The Thunderbird Blog
At Thunderbird, we firmly believe in the strength of listening to our community’s needs and wants, and balancing it with our resources and capabilities. While this has always been part of our ethos, we want to start 2026 by making our goals easier to read and comprehend at roadmaps.thunderbird.net, where you will find our roadmaps […]
NathSomewhere, someone finally made this and I think it's beautiful: https://www.thingiverse.com/thing:4687836
Ethernet | RJ45 clip to secure/repair/fix broken tab by guss67
This clip was design to fix/repair/secure the broken or loose tab of a RJ45 Ethernet connector and avoid crimping. Designed to prevent from moving, wiggling, falling from the connector and easy to install.UPDATE v.4.9 | 28/01/2021Added the 3 following files which have slightly wider body (0.25mm) than 4.7 version and small upgrade on the tip.1. "4.9.nf.supported" (extension) comes "with supports" for the ones are not very familiar with. But I still prefer S3D's supports.2. "4.9.nf" (extension) with "no fillet", to make it easier printing with supports.3. "4.9" (extension) with fillet, for "smooth edges". On FDM printers isn't that much noticeable.UPDATE v.4.7 | 01/01/2021Added another version with "no fillet" (".nf" extension), actually it has sharp edges to make it easier printing with supports.PrintingSuggested printing orientation is the one as the files are stored, why?Printing the tab from the base to the tip in X-Y axis makes it stronger and more flexible since its printed in one continued string.If you change the orientation with the tip on top then tab's base will start from the bottom and builds up while the Z axis is sticking the rest of it till the tip. With this orientation the tab has more possibilities to brake since Z layers don't bond the same as the method I suggested.*If you have another solution let me know.Supports Supports needed and you need to be experienced with good slicer settings. Also attention needed when removing them from the actual print.Or you can print the file with "4.9.nf.supported" (extension) which comes with supports. But I still prefer S3D's supports.Installation note:1.Before install the "printed clip" check the left overs of the broken tab. If it is too long the tip of the "printed clip" might not click underneath the left-over. So, I suggest to leave a length of the broken tab about "0,5-1,0mm". If the broken tad left-over is to small or cuted flash then the printed one might not click and hopefully that would work well, haven't tested that scenario.2.Follow the sketches to install the "printed clip", also while sliding in if you find it a bit hard some wiggling might help.*You may call it the "ScorpioNet" or "Devil's Network Tail"! Designed in InventorIf you enjoy and want to support my work you can donate me on the link below,Thank you!
VessOnSecurity
amy
Richard HughesNext week we're planning a big #fwupd release (with a lot of new exciting stuff) but the translations are looking a bit sad. Can anybody help? Thanks.
publictorsten