💡 New project! An USB powered LED desk lamp made of wood, ceramic, and aluminum. It will be called "Portuaria", which in Spanish means "related to the port", because its shape reminds me of the cranes and sailboats at the port.
🧵 #PortuariaLamp #lamp #prototype #LED #USB #lampdesign #woodenlamp #woodworking #electronics
I wanted the base of the lamp to be a 16 x 2 cm disc, but I only had 7 x 2 cm boards around here, so I ended up glueing a few cuts.
Then I cut a circle with the hand router using the guide as a compass, and sanded it with the orbital sander and sanding sponge.
Recycling ceramics to build a lampshade. I found that these mini bowls I made to test ceramic glazes roughly fit what I need for the lampshade of the prototype, so I drilled one to accommodate the LED and two screws.
The screws pass between the heatsink fins and will attach both the lampshade and heatsink to the wooden rod.
First attempt to mount the lamp head on the rod 🤔. What seemed easy in the drawing turned out not to be so easy when transferring it to materials.
The difficult thing was making the 3 mm slot in the 10 mm rod, and getting it to align with tolerances of less than 1 mm.
Next time I'm going to try with a router and templates, we'll see how it goes with that.
Stripping a cable to dress another 🤦♂️. The cable with a cotton textile sheath that I got is very thick compared to the diameter of the rods. The rods are 10 mm in diameter and the cable is 6.5 mm, so when drilling holes in the rods to pass the cable through there would only be 1.75 mm of wood left on each side.
So, I made a customized cable using the sheath of the original cable and an AWG 24 cable. The new one is 2.5 x 4 mm and fits perfectly in 4 mm holes 👍.
Assembling the head of the lamp. Despite the chamfered slot, it turned out pretty well. The yellow thing at the tip of the cotton sheath is a heat-shrink with glue, which is then inserted under pressure into the slot. It's the first thing that occurred to me to fix the sheath to the rod so that it can withstand the tension. Perhaps in the next iteration I will replace that with a screw, although the limited space is a challenge.
The LED I am using for the prototype lamps is one from the Bridgelux's Thrive series, which has a CRI of 98. The CRI is a color rendering index, which says how similar is the color rendering with the light from a LED compared to the rendering with natural light (which has a CRI of 100).
After using CRI 98 LEDs for a while, the CRI 90 ones look depressing, it's a one-way street 😁.
After a lot of experimenting with various models of the height-adjusting disc that holds the cable near the base, I decided that it would be better to make the height fixed instead of adjustable 🤷♂️
The main problem is that it is very difficult to make the adjustment fluid enough to adjust the height without the lamp jumping, which does not look good as a user experience.
This is the light spectrum emitted by the Bridgelux Thrive LED series compared to other ones that have a lower CRI.
You can see that the one from Bridgelux does not have the blue peak at about 450 nm that is present in the other LEDs in the chart.
That is why I chose it for this lamp prototype. If you were seeing a greenish tint in your "high" CRI 90 LEDs, now you know why 💡👀.
🧵 #PortuariaLamp #lamp #prototype #LED #CRI #lighting #spectrum #electronics
@leafmuncher The problem is this V8 COB is 12.5 x 12.5 mm, and that seems to be very unique. Bridgelux also makes Thrive COBs in 13.5 x 13.5 mm format (V6 HD Thrive), that is a more common format and I already found a holder for it on Digi-Key, so probably the next iteration of this lamp will use a V6 instead of a V8.
Fran 🇦🇷
Elan Feingold