I usually begin top side assembly with large but flat components like BGAs so I don't risk knocking tiny stuff around while placing them. Then smaller passives and ICs, and tall capacitors and connectors last.

This FPGA is the single most expensive component I've ever put on a board. Shipping an entire tray for one chip might be slight overkill though...

Out of the oven, BGAs all look good under side view optical microscopy (best I can do without X-ray).

Two 0402s needed touchup with an iron due to poor wetting; they were 33 ohm resistors from a reel I've had since 2014 so they might be starting to oxidize too much for my ROL0 flux to handle.

Tomorrow I'll populate the through hole connectors then start the bringup process.

All soldered up and ready to start bringup!

Later today after my little lab assistant goes to bed, that is. She's still a year or two from being ready to take readings off test points for me... Being able to speak in full sentences is probably a prerequisite.

These are just quick phone pics, I'll do some beauty shots with the A7R and macro lens later.

Fit testing the thermal solution. Looks mostly good, but not permanently mounting it yet. If i find problems early on it'll be easier to rework without a heatsink in the way.

I provisioned for two fans but we'll start with one and see how it goes.

The QDR-II+ heatsink is somewhat sheltered by the RS232 jack and probably won't see much airflow bit heatsinking it was more of a "just in case" vs the FPGA and main PHY which will definitely need it. So i think I'll be OK.

Kid is asleep so it's back to the lab for me.

After a bit of cable management we've got the first signs of life out of the board.

Applied 12V power to the input and it's drawing 3.6 mA. This is normal and expected, as all power rails are supposed to be off at this point other than the raw input and the 3.3V standby rail driven by an LDO to power the supervisor.

Next step is to put some code on the supervisor and start bringing up more power rails.

Spent a little while updating my STM32 peripheral library for the L031 (this was my first design using it) but I now have the PLL active and a blinky running at 16 MHz from flash.

Now to get a serial console up so I can get some more debug output besides a single LED...

Ok, UART is alive. Next step is to bring up a timer, then I'll have enough stuff working on the supervisor that I can begin actual power rail testing.

Can you tell I spend a lot of time in IDA? :P

Timer and logging framework are up. Ready to actually move forward with bringup.

So far the only rails that are active are 12V0_RAW (unregulated 12V prior to the main load switch) and 3V3_SB (3.3V standby for the supervisor), which is *very* in spec - averaging 3.30027V.

Next rail is 12V0, the core 12V power feed for all of the other DC-DC converters. This is driven by a load switch which limits slew rate so that I don't pull too much inrush current.

This is the first rail that's under software control from the supervisor.

It came up just fine and measures 11.9979V. Total power draw from the input climbed to 17 mA which doesn't sound unreasonable for five big DC-DC bricks.

Next is 1V0, the core power supply for the FPGA, QSGMII PHY, and SGMII PHYs. This is a big one with a lot of load on it, so lots of room for something to go wrong.

It came up perfectly as well, sitting at about 1.00015V. Overall input power draw is around 100 mA at 12V so an extra 83 mA. Assuming 90% conversion efficiency this means the board is pulling about 896 mA on 1V0 at idle!

In the interests of limiting potential damage to the expensive prototype if there's a short, the supervisor is pretty aggressive with timing and rail monitoring. If it commands a rail to come up and it fails to give PGOOD after 5 ms, it will automatically panic and shut down all power, then print a diagnostic message to the UART.

Unfortunately, the streak has come to an end with 1V2 which failed to come up within the (admittedly aggressive) 2 ms timeout. The automatic shutdown did its job and I don't think anything fried.

Next step: toss some probes down and see what's going on with that rail.