Climbing the learning curve on applying zip system flashing tape this morning. Glad I started on the walls and not the roof.

And before you ask; yes, I rolled the tape. #zipsystem

T-50 staples weren't cooperating going into the OSB, so while my gun isn't technically rated for them, you ARE able to buy 3/8" narrow crown staples. Short enough to not poke all the way through the 1/2 roof decking, but rigid enough to not be giving my any trouble stapling the insulation baffles to the bottom of the roof deck.

These baffles are because I'm doing a vaulted / cathedral ceiling in here, so this guarantees an air gap / path between the ceiling insulation and the roof decking. This allows air to flow from the lower soffit to the upper soffit to transport away any moisture that accumulates in these rafter bays and keeps the shingles cooler by having circulation behind them.

We are getting tantalizingly close to laying down the roof! All of it fits nicely in my pickup too.

Doesn't look too bad when it's all neatly piled on the ground. I'm sure I'll be fine and this part will be easy.

I'm shooting the trim paint on the fascia and rake boards before doing the roof. I figure it's easier to paint it now before I put the drip edge over it.

The dog only got lightly misted with white paint. She still mostly looks black.

Taking a break from the roof to stay out of the sun, you can get this disodium octoborate powder which you mix with water and spray on your bare studs before closing them in to prevent termite damage.

Am I really convinced this will make a huge difference? Not really. But for $13, it's pretty cheap insurance. And it isn't a question that we'll get termites in here; just a question of how fast and how bad.

Some people also just use Borax for the same thing, but structurally tetraborate and octoborate are different enough I figured I'd splurge for the real stuff.

So I put down the two rolls of asphalt paper that goes under the shingles. On steeper roofs, you can get away with just the zip system coating, but since I'm building only a 3/12 pitch roof, I need two layers of underlayment, so I can count the zip system as one, then put down 30 pound felt paper as the second.

Would you believe how much I came up short? I guess I'm going to buy a third roll, for the last nine freaking square feet.

Day one of putting shingles on the roof. I got through four bundles before the sun really came out and I called it quits.

Key take aways:
1) the part that wreaks you is carrying the 70 lb bundles up onto the roof. For larger projects, definitely worth getting the shingles delivered directly to the roof.

2) the little 1 gallon 0.5scfm trim compressor I own is able to keep up with one rookie shooting roofing nails absolutely no problem. Glad I didn't go buy/borrow/rent/steal a larger compressor for this project.

3) I'm definitely just paying someone to reroof my house when it comes time. My dad was freaking crazy when he replaced the roof on his house back in his prime. I, also, am past my prime.

You know how I came up 9 sq ft short on asphalt paper?

You will not believe how much I had left to do when I ran out of shingles tonight.

And we are done with the roof! 370 sq ft single slope shed roof with no penetrations. GAF HDZ shingles, pewter grey.

I never did find any manufacturer documentation about how to terminate the top of a single slope, nor reach out to customer service about it, so I ended up just winging it with some 3"x2" drip edge on top of the top course, with asphalt cement on top of every nail.

Now we restart at the ground and work our way back up to the eves with siding and trim.

In the interest of preventing water intrusion under the wall, I used a diamond wheel on my angle grinder to cut a groove in the concrete, then set a strip of flashing into a bead of wet sealant in the groove.

For my next shed, I'm just going to build it on a raised foundation. This sucked.

YES! I finally found a sheet metal shop who was willing to bend me the eight sticks of a custom Z bar profile I needed for the kick trim around the bottom of my shed.

Art's Sheet Metal Mfg. Came in with a post-it note drawing of what I needed, they pulled out their sample ring of thicknesses, and asked "do you need this this afternoon or tomorrow?"

$80 for 80 feet was practically off the shelf retail price, so we are finally unstuck on the siding.

Finished the flashing and zip tape around the perimeter of the wall today. I cut a groove into the concrete, then wet set the flashing into some sealant in the groove and zip taped the top of the flashing. So I'm really hoping this helps prevent any water coming in under the wall.

On top of this goes a PVC trim board, the Z flashing I've had so much difficulty finding, and then we can finally get started on the trim and siding over the OSB.

So this is where we're at at this point.

Next things on the list is boxing in the soffits, trim along the bottom and all the edges, two more windows on the back wall, then we can start hanging horizontal lap siding.

Then lots and lots of work on the inside.

The soffit vent for the lower eves has been put in. The rest of this surface gets closed in with 1/2 ACX plywood, and this perforated vent allows air to flow up into the eve, across the bottom of the roof sheathing, and out a similar vent in the top eves. This will keep the shingles significantly cooler and give any moisture in my ceiling cavity a path out of the building.

These vents are also not straight. Because the fascia boards aren't straight. Because the rafters weren't straight. Because one of the walls is slightly crooked. And I just need to come to terms with the fact that this shed is still going to look really good when a normal human being looks at it.

Finished boxing in the upper soffit. It isn't perfect, but it's up high, and nothing some caulk and trim won't be able to hide later.

Still better than fighting with beauty boards and roofing nail punch though and block vents, etc etc etc.

The 8' sticks of soffit vent were about $25, plus all the boarding is just ACX plywood.

Normally you wouldn't have an "upper" soffit, but would have ridge vents in your roof. This only exists because I'm building a single slope "shed" roof to maximize the number of solar panels we can add later.

Got all of the trim and a bit of the siding delivered for the shed.

The delivery guy actually remembered me from when he dropped off the original lumber package a year ago and the first words out of his mouth were "wow! You did it! That shed is looking great for being your first building"

😁 So work continues.

I chickened out and only ordered a bit of the siding so I didn't have an ENTIRE sheds worth of siding dropped in my front yard all at once.

I'm still optimistic about this red color. ❤️