Anybody know anything about gear motors and where to search for them?
https://lemmy.world/post/34778537
Anybody know anything about gear motors and where to search for them? - Lemmy.World
I’ve been tasked with finding gear motors to replace a model that we use. If I’m
looking for something exact, I can usually find what I need, but if I have a
margin of error for what I need, it gets harder to find what I want. As an
example, I need a right angle gear motor running at 90vdc. Fine so far. But I
can use anything around 1/7 to 1/10 HP, and approximately 90 RPM with a decent
margin of error both ways. We don’t care where it comes from, but I don’t even
know where to look.
Clipboard saves history across sessions even when set up not to
https://lemmy.world/post/25611487
Clipboard saves history across sessions even when set up not to - Lemmy.World
I’m running KDE on Nobara, and every time I power on my computer, there’s
something in the clipboard leftover from the previous session despite that
setting being turned off. I’m not 100% sure, but sometimes I think that it’s not
even the last thing I copied. I’d have to make a mental note to check every
time. Is there something I can do to fix this besides the basic system settings
dialog?
[https://lemmy.world/pictrs/image/05d13f1b-4591-4f6a-ba48-6697962a40af.png]
Need some help. System locked up, had to force power off, now gaming performance is bad.
https://lemmy.world/post/23821810
Need some help. System locked up, had to force power off, now gaming performance is bad. - Lemmy.World
I was playing Ark Survival Ascended when my system locked up. No response from
the mouse or keyboard, screen frozen, sound loop about 1 second long. I let it
sit for a minute, thinking maybe it’ll break out of it, and eventually had to
force the power off with the power button. I restarted my system, and now my
performance in games is really bad, I’m getting about 20fps where I used to get
80-100, sometimes it gets so bad it goes into the single digits. I get
stuttering sound as well and some pretty bad input lag. In Ark, I can see the
textures slowly pop in over time, which normally happens in a matter of a second
or two. Looking at CoreCtrl, if I set it to high performance mode, the GPU’s
power usage peaks around 150 Watts instead of 300+. I’m running Nobara on a
7900X3D and an RX 7900XT with 32GB RAM. Not sure how to go about diagnosing my
issue here. I haven’t made any software changes, so I’m a little lost as to why
this would happen.
For any Canadians, Spool3d.ca has some nice deals going on
https://lemmy.world/post/22584145
For any Canadians, Spool3d.ca has some nice deals going on - Lemmy.World
Like the Ender 3 V3 SE at $200 and the Ender 3 S1 Pro at $250. They don’t seem
to have any interesting deals on consumables, sadly.
Gamescope and PS4 controller - Lemmy.World
I just bought a nice OLED monitor and I’m trying to take advantage of it to play
my games in HDR. If I run my games in gamescope, then HDR runs fine but my PS4
controller doesn’t work. If I play without gamescope, the controller works, but
HDR does not. I’ve been trying to figure this out for a bit, and some people
have been having some luck with the -e flag, which does nothing for me.I’ve
tried Steam Input and overlay in all combinations of enabled and disabled and
I’ve tried in big picture/gamepadui. Either way I have to choose between HDR and
the controller. Has anyone gotten this to work?
Object proportions are off in the slicer compared to Blender
https://lemmy.world/post/2358653
Object proportions are off in the slicer compared to Blender - Lemmy.world
I modeled an object in Blender intending to print it, but when I import it into
PrusaSlicer or Cura, the dimensions don’t quite match. In Blender, the
dimensions are 178mm x 142mm, but when I import it into Cura or PrusaSlicer, it
imports it as 180 x 138mm. I can manually adjust the dimensions, but why is this
happening? And will it mess up my fit in the end? Who do I trust here? I don’t
want to waste hours printing for nothing.
Khruangbin @ Villain | Pitchfork Live
https://lemmy.world/post/2326593
Khruangbin @ Villain | Pitchfork Live - Lemmy.world
I’ve been listening to this a bunch lately. This is the cleanest-sounding
concert recording I’ve ever found on youtube.
Any chefs or connoisseurs to tell me if I'm crazy for this idea?
https://lemmy.world/post/2264709
Any chefs or connoisseurs to tell me if I'm crazy for this idea? - Lemmy.world
I want to put grilled paneer, arugula, and salmon roe on a cracker as an
appetizer or early snack. I feel like the salty/umami roe with the
bitter/peppery freshness of arugula on the grilled paneer would taste nice. In
terms of texture there would be the chewy/squeaky cheese, the crispy cracker,
and the pop of the roe. I’m thinking a cracker like a triscuit, but I feel like
they’re too thick for what I’m trying to put together. Anyway, before I spend
time and money to make a concoction that tastes like garbage, does anyone have
any opinions or suggestions?
What can I do about internal walls that can't be seen?
https://lemmy.world/post/2222011
What can I do about internal walls that can't be seen? - Lemmy.world
I have a model I want to print that has multiple layers of internal walls. They
are useless and can’t be seen in the finished product, like a hollow cylinder
inside another hollow cylinder. I can’t seem to figure out how to prevent the
slicer from including those useless parts. I’ve tried with Cura and PrusaSlicer.
Is there another tool I should be using for this?
Automating Spotify downloads? - Lemmy.world
Is there a way to automatically locally save Spotify music as I listen to it? Or
to access/convert the files that Spotify saves for offline playback?
