Yeah, I also used to like AvE’s tool teardowns, I felt he did a good job explaining the little things you wouldn’t think about, where companies cut costs, and if those cost/perf tradeoffs were done in a smart way or if it would bite you.

Enter covid, and he’s ranting about US politics and trucker convoys. Unsubscribed and haven’t watched him since, tbh the channel was going downhill before then, but that was the straw that broke the camels back.

Sad to hear he kept up with the bad views, but not surprising.

He does little bursts of running with periods of walking in between, so I dont think it would work. Perhaps with other cats it would though

Take out any spinning rust and pack those in a foam HDD case. Number them as you pull them for easy reinstall.

Put a bit of plywood under the rack, ratchet strap it, and now you can put it on a dolly without the lip hitting the equipment as you try and lift it. For avoiding it falling off the dolly, use a 2nd ratchet strap and wrap it around the chassis / dolly.

Put a 2nd piece of plywood on top once its in the uhaul so you can load more boxes on top… Maybe even do that at first so the initial strap is securing it as well.

As for the bottom plywood, if you add some felt pads, then it will help you shimmy the chassis into / out of its position once its unloaded. I have my rack vhb taped to ply with felt under it and recommend it to people IRL a fair bit.

Take out any spinning rust and pack those in a foam HDD case. Number them as you pull them for easy reinstall.

Put a bit of plywood under the rack, ratchet strap it, and now you can put it on a dolly without the lip hitting the equipment as you try and lift it. For avoiding it falling off the dolly, use a 2nd ratchet strap and wrap it around the chassis / dolly.

Put a 2nd piece of plywood on top once its in the uhaul so you can load more boxes on top… Maybe even do that at first so the initial strap is securing it as well.

As for the bottom plywood, if you add some felt pads, then it will help you shimmy the chassis into / out of its position once its unloaded. I have my rack vhb taped to ply with felt under it and recommend it to people IRL a fair bit.

oh thanks for the heads up!

Yeah, or even something in the middle where you still use a cheap microcontroller and the hall effect sensor to track distance without any treats. You would have to find a way to get the cat running in the first place though.

It seems like people have better luck getting the larger semi-domesticated savannah cats / similar to use the wheel than domestic house cats without training

I wanted to make a human sized wheel to bring to opensauce that dispenses candy thats the equivalent to the calories you burned, or possibly had motors acting as a generator that powered up a power bank for people to charge their phones from!

Thanks for the feedback though, and glad you liked it :)

smb share if its desktop to desktop. If its from phone to PC, I throw it on nextcloud on the phone, then grab it from the web ui on pc.

Smb is the way to go if you have identity set up, since your PC auth will carry over for the connection to the smb share. Nextcloud will be less typing if not since you can just have persistent auth on the app / web.

Its just a test to dial your printer in. I shimmed my bed with 0.1mm washers. I haven’t done a full square of plastic, but I printed my first layer / z-offset print of choice in all 4 corners and center in order to verify the bed level results in octoprint were accurate.

Before hand 70% of my bed printed perfect, but one spot was a little lower, and the mesh bed leveling wasn’t accounting enough for it. Parts printed on textured sheets would not pick up the texture as well in that one spot. I like the textured look for top surfaces of control panels and such, so having an area on the bed that wouldn’t apply the texture was a bit annoying.

Tests like what you are talking about is an extreme way to verify that everything is square, or at least well accounted for in the firmware.

Also, since this wasn’t something achievable out of the box until recently, printer manufacturers are showing it off as a point of pride / as a sales tactic.