szczuroarturoAntivirus recomendations
bushvinI wouldn’t recommend using anti-virus software. It usually creates a lot more overhead, plus it usually mimics existing solutions already in linux. The only viruses I have ever caught using an anti-virus software on Linux are the test viruses to see if all is working fine.
Anyway, here’s my 20+ enterprise experience recommendations with Linux :
- enable secure boot: will disable launching non-signed kernel modules (prevent root kits)
- enable firewall: and inly allow ports you really need.
- SELinux: it is getting better, and it will prevent processes to access resources out if their scope. It can be problematic if you don’t know it (and it is complex to understand). But if it doesn’t hinder you, don’t touch it. I do not know AppArmor, but it is supposed to be similar.
- disable root over ssh: or only allow ssh keys, or disable ssh altogether if you do not need it.
- avoid using root: make sure you have a personal account set up with sudo rights to root WITH password.
Adhering to these principles will get you a long way!
pglpmThank you for the advice!
Firewall on Linux is something I still don’t understand, and explanations found on Internet have always confused me. Do you happen to know some good tutorial to share? Or maybe one doesn’t need to do anything at all in distros like Ubuntu?
Regarding ssh: you only mean incoming ssh, right?
Firewall - While this tutorial is Ubuntu 16.04 it should work current versions of Ubuntu
linuxbabe.com/…/getting-started-gufw-ubuntu-16-04
It should work for other distributions once you change the package manager.
ebtables and iptables can be very complex. And I failed my 1st RHCE exam because of them. But once you learn, you will never unlearn, as they are quite beautifully crafted. You just need to get into the mindset of the people who wrote the tools…
Look into firewalld
It has a rather simplified cli interface: firewall-cmd
The manpages will tell you a lot.
firewall-cmd —add-service=ssh
Will open the ports for your ssh daemon until you reload your firewall or reboot your system
firewall-cmd —permanent —add-service=ssh
Will open the ssh ports until you remove them
firewall-cmd —list-all
Will show you the current firewall config
Try nftables directly, it’s simple and straightforward, scripting syntax is easy.
Another simpler frontend for iptables I think is well suited for desktop environemnts is ufw. It does what it’s supposed to do and is extremely simple to use
I personally do not know ufw, but if it does what it must, then you’re solid.
Linux is also about choices: do stuff the way you choose to, and makes you comfortable.
Yes, usually you configure your endpoint firewall to block incoming traffic, while allowing all outgoing.
Unless you’re in a very secure zone, like DMZ’s.
GhostWhat don’t you completely understand about Linux firewall? I don’t mind helping you learn
Thank you everyone, also @[email protected] @[email protected].
For example, if I open my settings (I’m on Ubuntu+KDE) I don’t see any firewall settings to configure. So I expect this is automatically done by the OS, but maybe I’m wrong. A bit surprised that the system itself doesn’t recommend using a firewall, to be honest.
Many firewall tutorials start speaking about “your server”. Then I wonder: is this really for me? I don’t have a server. Or do I?
I now see that the tutorial from @[email protected] gives a better explanation, cheers! So I see it’s good to have a firewall simply because one connects to public wifis from time to time.
I see that both UFW and firewalld are recommended… is it basically OK whichever I choose?
The main one everybody uses at least from my knowledge and from what I’ve used over the last 13 years is UFW. That is what you want to use.
A firewall is very important not just for being on public Wi-Fi connections. A firewall is your extra layer of protection
I don’t know what Distro you run. But it’s almost the same for each one
digitalocean.com/…/how-to-set-up-a-firewall-with-…
UFW is installed by default on Ubuntu. If it has been uninstalled for some reason, you can install it with sudo apt install ufw.
Using IPv6
sudo nano /etc/default/ufw
That command should come back with this
IPV6=yes
Save and close the file. Now, when UFW is enabled, it will be configured to write both IPv4 and IPv6 firewall rules. However, before enabling UFW, we will want to ensure that your firewall is configured to allow you to connect via SSH. Let’s start with setting the default policies.
Setting up default policies
sudo ufw default deny incoming sudo ufw default allow outgoing
These commands set the defaults to deny incoming and allow outgoing connections. These firewall defaults alone might suffice for a personal computer, but servers typically need to respond to incoming requests from outside users. We’ll look into that next.
Allowing SSH connections:
sudo ufw allow ssh
This will create firewall rules that will allow all connections on port 22, which is the port that the SSH daemon listens on by default. UFW knows what port allow ssh means because it’s listed as a service in the /etc/services file.
However, we can actually write the equivalent rule by specifying the port instead of the service name. For example, this command works the same as the one above:
sudo ufw allow 22If you configured your SSH daemon to use a different port, you will have to specify the appropriate port. For example, if your SSH server is listening on port 2222, you can use this command to allow connections on that port:
sudo ufw allow 2222Then enable
sudo ufw enable
The main one everybody uses at least from my knowledge and from what I’ve used over the last 13 years is UFW. That is what you want to use. I could easily say that for firewalld… 😃
Ufw is typically available/pre-installed with Debian based systems (Debian, Ubuntu, zzz), while Firewalld is typically available on Red Hat Enterprise Linux and derivates (Fedora, CentOS, Rocky, …)
But it boils down to what you prefer, really.
I know all this already. But I also use arch and have been for the last 6+ years and I use ufw lol
I see that both UFW and firewalld are recommended… is it basically OK whichever I choose?
Yes. Whichever works for you should be fine. In the end you should be able to manage it
ChonkaLoogo with firewalld ufw floods dmesg with useless messages
I don’t think you need to configure your firewall.
Firewalls are usualy used to block incomming connectings. Usualy a Firewall that blocks all incomming connections is already active on your modem/router. Adding exception to the modem/router Firewall usualy happen through port forwords.
@[email protected] @[email protected] @[email protected] @[email protected] @[email protected]
Thank you ALL for the great advice and guides! I’m writing from behind a laptop firewall now, and don’t notice anything :) It was smoother than I expected. In the end I used UFW because it was already installed, but I’ll take a look at firewalld too in some days!
Really great people here at Lemmy :)
You’re welcome friend!